Cabletron-systems 9000 Instrukcja Użytkownika Strona 1

9031125-03 SmartSwitch 90009C114 and 9C714 ChassisInstallation Guide

Installing the 9Cx14 Chassis1-2 Redundant Power Supply Modules The 9C114 and 9C714 support the installation of two power supplies for power supply re

1-3Installing the 9Cx14 Chassis The descriptions of the seven backplane buses are as follows: System Management Bus 1 The System Management Bus 1, ab

Installing the 9Cx14 Chassis1-4 The Cell Transfer Matrix (installed in the 9C714 chassis only) The Cell Transfer Matrix provides a Time Division Mult

1-5Installing the 9Cx14 Chassis Site Guidelines The following guidelines must be followed to select a suitable site for the SmartSwitch 9000. If not,

Installing the 9Cx14 Chassis1-6 Installation Order Once a suitable site has been chosen, the SmartSwitch 9000 may be installed. The unit may be free

1-7Installing the 9Cx14 Chassis Rack Mounting the Chassis The chassis can be mounted in a standard 19-inch equipment rack. If the rack is not secured

Installing the 9Cx14 Chassis1-8 Installing a Power Supply At least one power supply must be installed on the rear of the MMAC-Plus chassis. Additiona

1-9Installing the 9Cx14 Chassis Figure 1-3. Installing a Power Supply100-125v-12A200-250v-6A50-60 HzPOWER SUPPLY MODULE9C214-1100%50%0%STATUSPWRSNBLo

Installing the 9Cx14 Chassis1-10 Attaching the Electrostatic Discharge (ESD) Wrist Strap The ESD Wrist Strap must be attached before handling the Env

1-11Installing the 9Cx14 Chassis Installing the Environmental Module The Environmental Module is installed in the slot above the module card cage in

Installing the 9Cx14 Chassis1-12 Figure 1-5. Installing the Environmental Module Installing SmartSwitch 9000 Interface Modules SmartSwitch 9000 Inter

1-13Installing the 9Cx14 Chassis 5. Install the Interface Module in the chassis by sliding it in any available slot and locking down the top and bott

Installing the 9Cx14 Chassis1-14 Attaching 9C614 INB Terminator Modules Two 9C614 INB Terminator Modules must be attached to the rear of the SmartSwi

1-15Installing the 9Cx14 Chassis Figure 1-7. Attaching the INB Terminator Modules Powering up the SmartSwitch 9000 The SmartSwitch 9000 chassis is po

Installing the 9Cx14 Chassis1-16 5. Check that all LEDs on the INB Terminator Module are green.If the LEDs are any color other than green, refer to t

1-17Installing the 9Cx14 Chassis Weight Unit: 19.96 kilograms (44 pounds)Shipping: 24.95 kilograms (55 pounds) 9C714 MMAC-Plus Chassis Dimensions 76.

Installing the 9Cx14 Chassis1-18 9C614 INB Terminator Module Dimensions 21.59 H x 2.22 W x 14.92 D centimeters(8.5 H x 0.875 W x 5.875 D inches) Wei

iNotice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

iiiNotice Declaration of ConformityAddendum Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Man

Noticeiv

v Contents Chapter 1 Installing the 9Cx14 Chassis The SmartSwitch 9000...

Contentsvi

1-1 Chapter 1 Installing the 9Cx14 Chassis This document contains information necessary to install the SmartSwitch 9000 9C114 and 9C714 chassis. It i