Cabletron-systems 6H258-17 Instrukcja Użytkownika

90333816H258-17 and 6H259-17SmartSwitch 6000 Interface ModulesInstallation User’s Guide

viii If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addi

ixSAFETY INFORMATIONCLASS 1 LASER TRANSCEIVERSTHE GPIM-01 AND GPIM-09 GIGABIT ETHERNET MODULESUSE CLASS 1 LASER TRANSCEIVERS. READ THE FOLLOWING SAFET

xDECLARATION OF CONFORMITYApplication of Council Directive(s): 89/336/EEC73/23/EECManufacturer’s Name: Cabletron Systems, Inc.Manufacturer’s Address:

xiContentsFigures... xiiiTabl

xii2NETWORK REQUIREMENTS2.1 100BASE-FX Network... 2-12.1.1 Multimode

xiiiFiguresFigure Page1-1 The SmartSwitch...

xivTablesTable Page3-1 Contents of SmartSwitch Shipping Container...3-14-1 LANVIEW LEDs ...

xvAbout This GuideWelcome to the Cabletron Systems 6H258-17 and 6H259-17 SmartSwitch 6000 Interface Modules User’s Guide. This guide describes the 6H2

Structure of This GuidexviSTRUCTURE OF THIS GUIDEThis guide is organized as follows:This About This Guide preface provides preliminary information tha

Related ManualsxviiRELATED MANUALSThe following manuals may help the user to setup and manage the SmartSwitch modules:• SmartSwitch Series 6H202, 6H20

Document ConventionsxviiiDOCUMENT CONVENTIONSThe following conventions are used throughout this document:NOTENote symbol. Calls the reader’s attention

Introduction 1-11IntroductionThis chapter introduces the 6H258-17 and 6H259-17 SmartSwitch 6000 interface modules and provides information about how t

Overview1-2 IntroductionFigure 1-1 The SmartSwitchPort Status LEDsCPU LEDCOM PortNetworkPorts 1-16ResetVHSIM/HSIM Slot

OverviewIntroduction 1-31.1.1 ConnectivityThe SmartSwitch modules connects to Fast Ethernet networks or workstations through the MT-RJ fiber optic por

Overview1-4 Introduction1.1.4 SmartTrunkSmartTrunk, also referred to as SmartTrunking, is Cabletron Systems’ terminology for load balancing or load sh

OverviewIntroduction 1-5The analyzer or RMON probe will see the data as if it were directly connected to the LAN segment of the source port. The VLAN

Overview1-6 Introductionand GMRP handle frames under GARP, and how to configure the switch ports to take advantage of this operation, refer to Local M

OverviewIntroduction 1-71.1.13 Switching OptionsSmartSwitches provide 802.1Q switching or SecureFast Switching Virtual Network Services between all of

Getting Help1-8 Introduction1.1.17 LANVIEW Diagnostic LEDsLANVIEW diagnostic LEDs serve as an important troubleshooting aid by providing an easy way t

Network Requirements 2-12Network RequirementsBefore installing the SmartSwitch modules, review the requirements and specifications referred to in this

iNOTICECabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. T

SmartTrunk2-2 Network Requirements2.1.2 Single Mode Fiber Optic CablingThe single mode fiber optic module, the 6H259-17, operates at a nominal wavelen

Installation 3-13InstallationThis chapter covers the following items:• Unpacking the SmartSwitch (Section 3.1)• Installing Options (Section 3.2)• Inst

Installing Options3-2 Installation3.2 INSTALLING OPTIONSIf installing an optional HSIM or VHSIM, it must be installed in the SmartSwitch before procee

Installing the SmartSwitch into the 6C105 ChassisInstallation 3-3Figure 3-1 Installing an Interface Module5. Examine the module for damage. If any dam

Connecting to the Network3-4 Installation6. Locate the slot guides that line up with the number of the slot in which the module will be installed. Ins

Connecting to the NetworkInstallation 3-5.Figure 3-2 Connecting a Fiber Optic Segment to the SmartSwitchConnect a fiber optic segment to the SmartSwit

Completing the Installation3-6 Installation3. Verify that a link exists by checking that the port RX (Receive) LED is ON (flashing amber, blinking gre

Troubleshooting 4-14TroubleshootingThis chapter provides information concerning the following:• Using the LANVIEW diagnostic and status monitoring sys

Using LANVIEW4-2 TroubleshootingFigure 4-1 LANVIEW LEDsReceive LEDTransmit LEDCPU LED

Using LANVIEWTroubleshooting 4-3Table 4-1 LANVIEW LEDs LED Color State Recommended ActionCPU Off Power off. Power up chassis.Red Blinking. Hardware fa

iiFCC NOTICEThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause ha

Using LANVIEW4-4 TroubleshootingTX Off Port enabled, and no activity. Should flash green every two seconds indicating BPDUs being sent if STA is enabl

Troubleshooting ChecklistTroubleshooting 4-54.2 TROUBLESHOOTING CHECKLISTIf the SmartSwitch is not working properly, refer to Table 4-2 for a checklis

Troubleshooting Checklist4-6 TroubleshootingTable 4-3 Power System TroubleshootingPossible Causes InstructionLoss of Power to the 6C105 chassis.Perfor

Troubleshooting ChecklistTroubleshooting 4-7Table 4-4 Firmware TroubleshootingPossible Causes InstructionAutobaud enabled. Press ENTER (RETURN) (may t

Troubleshooting Checklist4-8 TroubleshootingTable 4-5 Management System TroubleshootingPossible Causes InstructionImproper Community Names Table.1. Re

Troubleshooting ChecklistTroubleshooting 4-9Table 4-6 Device Setup TroubleshootingPossible Causes InstructionThe SmartSwitch detect a looped condition

Using the RESET Button4-10 Troubleshooting4.3 USING THE RESET BUTTONThe RESET button located near the upper plastic locking tab of the module (refer t

Specifications A-1ASpecificationsThis appendix provides operating specifications for the Cabletron Systems 6H258-17 and 6H259-17 Interface Modules. Ca

Environmental RequirementsA-2 SpecificationsA.3 ENVIRONMENTAL REQUIREMENTSA.4 INPUT/OUTPUT PORTSA.5 COM PORT PINOUT ASSIGNMENTSThe COM port is a seria

Regulatory ComplianceSpecifications A-3A.6 REGULATORY COMPLIANCE6H258-17 Specifications (Ports 1 through 16): Fast Ethernet 100 Mbps (100BASE-FX compl

iiiCABLETRON SYSTEMS, INC.PROGRAM LICENSE AGREEMENTIMPORTANT:THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS:CANADAMEXIC

Switch Settings, Upgrades, and Installations B-1BSwitch Settings, Upgrades, and InstallationsThis appendix covers the following items:• Setting the mo

Setting the Mode SwitchesB-2 Switch Settings, Upgrades, and InstallationsFigure B-1 shows the location of the mode switches and the switch settings fo

SIMM UpgradeSwitch Settings, Upgrades, and Installations B-3• After changing the position of switch 6 and restarting the module, the SmartSwitch reque

SIMM UpgradeB-4 Switch Settings, Upgrades, and InstallationsFigure B-2 SIMM Slot LocationsB.2.2 Installing the DRAM SIMMTo install a DRAM SIMM, refer

Installing Optional High Speed Interface ModulesSwitch Settings, Upgrades, and Installations B-5Figure B-3 Installing the DRAM B.3 INSTALLING OPTIONAL

Installing Optional High Speed Interface ModulesB-6 Switch Settings, Upgrades, and InstallationsFigure B-4 HSIM and VHSIM Connector LocationsOptional

Index-1Numerics100BASE-FXconnection 3-4requirements 2-1CCable Specifications100BASE-FX network 2-1COM portpin assignments A-2Connecting to the network

Index-2SSafety A-2Safety informationlaser ixSDRAMinstallation B-5SIMMsinstallingLDRAM B-4location B-3SmartTrunkintroduction to 1-4Specifications A-1St

ivIf the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in additio

vCABLETRON SYSTEMS SALES AND SERVICE, INC.PROGRAM LICENSE AGREEMENTIMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA

vi5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely at private expense; (ii) contains “restricted computer

viiCABLETRON SYSTEMS LIMITEDPROGRAM LICENSE AGREEMENTIMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS: